Est.

Guide

CTAF vs UNICOM: What Each Frequency Is For

CTAF is the frequency pilots use to announce themselves at an airport without an operating tower; UNICOM is a ground station that may answer. How they differ, where they overlap and which one to use.

A reference guide from Am I Cleared to Land · Last checked against FAA publications November 15, 2026

The short answer

CTAF (Common Traffic Advisory Frequency) is a job a frequency does: it is the one common frequency every pilot uses to announce position and intentions at an airport without an operating control tower. UNICOM is a station: a non-government radio, usually run by the airport or an FBO, that may answer with wind, runway and fuel information. At many fields the UNICOM frequency is also the CTAF, which is why the two get confused. Either way, nobody on it can clear you to land.

CTAF and UNICOM side by side

CTAFUNICOM
What it isA designated frequency for airport advisory practices at an airport without an operating towerA non-government air/ground radio station at a public-use airport with no tower or FSS
Who is on itEvery radio-equipped pilot arriving, departing or in the patternA ground operator (often the airport or FBO) when staffed, or an automated system
Which frequencyWhatever the publications name: a UNICOM, MULTICOM (122.9), FSS or part-time tower frequencyOne of 122.700, 122.725, 122.800, 122.975, 123.000, 123.050 or 123.075 at non-towered airports; 122.950 at airports with a tower or FSS
Who you addressOther traffic: "[Airport] traffic …"The station: "[Airport] UNICOM …"
What you get backPosition reports from other pilots, if they are talkingOn request, and when someone is there: wind, recommended runway, weather and services such as fuel
AuthorityNone. It is pilots informing each otherNone. UNICOM operators are not air traffic controllers and do not issue clearances

What CTAF is

The Aeronautical Information Manual (AIM 4-1-9) defines CTAF as a frequency designated for carrying out airport advisory practices while operating to or from an airport without an operating control tower. It names a purpose, not a type of station. The frequency that does the job may be a UNICOM, a MULTICOM, an FSS (in Alaska) or a tower frequency.

The whole system rests on everyone choosing the same frequency and using the airport's correct name, so that pilots can find each other by ear before they find each other by eye. No one assigns sequence or separation on a CTAF: each pilot self-announces, listens, and sees and avoids.

What UNICOM is

UNICOM is a non-government air/ground station that may provide airport information at public-use airports where there is no tower or FSS. On a pilot's request it may give weather, wind direction, the recommended runway and other information, and it is the frequency to ask about fuel or a ride. It is licensed through the FCC, which also designates the frequencies it may use.

Many airports now run an automated UNICOM that answers microphone clicks with automated weather, a radio check or airport advisory information. Where it exists, the Chart Supplement and approach charts say so.

A UNICOM is staffed when someone is there to staff it. An unanswered call is common, and an answer is information, not an instruction.

When the UNICOM frequency is the CTAF

At many non-towered airports with a UNICOM, the UNICOM frequency is designated as the CTAF, and the Chart Supplement lists it as "CTAF/UNICOM" followed by one frequency. You use that one frequency in two ways: you call "[Airport] UNICOM" to ask the ground station for wind and runway, and you call "[Airport] traffic" to tell other pilots where you are.

The two can also differ. At an airport with a part-time tower, the CTAF when the tower is closed is often the tower frequency, while UNICOM sits on another frequency (122.950 at airports with a tower or FSS on the field, where wind and runway information may not be available). At an airport with no tower, FSS or UNICOM, the CTAF is MULTICOM, 122.9.

On a sectional chart, a frequency followed by a C in a solid circle is the CTAF, and the UNICOM frequency is printed at the end of the airport's data line. Charts lag changes: confirm both in the current Chart Supplement before you fly.

Which frequency to use, airport by airport

AIM Table 4-1-1 sets out the recommended practice for each kind of airport:

At the airportUse
UNICOM, no tower or FSSCall the UNICOM station on the published CTAF. If no one answers, self-announce on the CTAF.
No tower, FSS or UNICOMSelf-announce on MULTICOM, 122.9.
Tower or FSS not in operationSelf-announce on the published CTAF.
FSS open, no tower in operation (Alaska only)Communicate with the FSS on the CTAF.

Arriving, monitor and talk on the CTAF from 10 miles out to landing. Departing, stay on it from start-up and taxi until 10 miles from the airport, unless the regulations or local procedures say otherwise. Pilots overflying or manoeuvring within 10 miles at pattern altitudes should monitor it too.

What to say on each

Say the airport's name at the start and end of every call: other airports nearby may share the same UNICOM or MULTICOM frequency. Name the runway by number, never "the active". The AIM's own examples, with Frederick as the airport:

  1. Frederick UNICOM, Cessna 801TF, 10 miles southeast, descending through [altitude], landing Frederick, request wind and runway information, Frederick.
  2. Frederick traffic, Cessna 801TF, entering downwind runway one niner, full stop, Frederick.
  3. Frederick traffic, Cessna 801TF, clear of runway one niner, Frederick.
  4. Frederick traffic, Cessna 801TF, departing runway one niner, departing the pattern to the [direction], Frederick.

Report about 10 miles out, entering downwind, base and final, and leaving the runway; departing, report before taxiing and before taxiing onto the runway. "Traffic in the area, please advise" is not a recognised call and the AIM says not to use it.

What neither frequency can do

  • Neither gives a clearance. There is no one at a non-towered field to clear you to land; the question the radio answers is who else is out there.
  • Neither guarantees you hear everyone. Aircraft without radios may legally use many non-towered airports, and pilots sometimes do not transmit.
  • A UNICOM answer can be out of date, and the runway it recommends is advice. The pilot picks the runway and follows the published pattern.
  • A busy shared frequency can bury a call from the airport you need under calls from the airports around it, which is why the airport name begins and ends each call.

The CTAF is often also the frequency that turns on pilot-controlled runway lighting at night. Whether a field has it, and on which frequency, is in the Chart Supplement.

Where to check an airport's frequencies

  • The FAA Chart Supplement entry for the airport: CTAF, UNICOM, tower hours and lighting.
  • Sectional and terminal area charts: the airport data block.
  • Instrument approach and departure procedure charts, which list the CTAF.
  • Any Flight Service Station, by radio or phone, and the NOTAMs for the airport, for changes since the charts were printed.

Sources

  1. AIM 4-1-9: Traffic Advisory Practices at Airports Without Operating Control Towers
  2. AIM 4-1-11: Designated UNICOM/MULTICOM Frequencies
  3. FAA Advisory Circular 90-66C, Non-Towered Airport Flight Operations
  4. FAA Chart Supplement (digital)

Frequencies change. Check the current Chart Supplement and NOTAMs for any airport before you fly; this guide is not a substitute for them.

Further reading